Can I Set Up A Bathtub Myself?
Can I Set Up A Bathtub Myself?
Blog Article
Here down the page you can get some outstanding points involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and often, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably hard project. If the old bathtub is easily obtainable, the project can move easily; if you have to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will need a helper to leave the old bathtub and also set in the new one. Ensure you have actually certified yourself for the task as well as fit trying it. As opposed to hiring a professional to take over a halfway-completed project, it is better to consider utilizing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will certainly assist you set up a brand-new tub in your bathroom if you have already gotten a brand-new tub as well as do not require to transform the plan of your previous water pipelines.
Your devices and also product list should comprise the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you must do is detach the water system. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing taps can be fairly bothersome because of the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipelines. When the supply pipes have actually been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Before proceeding to fit the new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin ensuring that the washing machines are in location between the faucet and the sink. Protect the tap in position with the manufacturer supplied backnut. Once the faucet is securely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be linked to the tap ends initially, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Bath tub
Using the two wood boards under its feet, place the bathtub in the needed placement. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the tub till the level reviews level.
To install faucets, fit all-time low of the outermost flexible faucet connector to the suitable supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water supply and inspect all joints and also brand-new pipework for leakages and tighten them if required. Fill up the bath tub as well as additionally check the overflow outlet as well as the typical outlet for leaks.
Lastly, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub needs to wait until the bathtub has been used at least once as this will settle it into its final setting.
Getting ready for the Setup
First of all, the sustaining framework supplied with the bath ought to be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final position.
Tiling Around the Bathtub
In the location where the bathroom satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a stiff seal, causing the water to penetrate the wall surface between the bath and also the tiling, causing issues with wetness as well as possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can crack relatively early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly available on the marketplace. It is suggested to fit the tiles making use of water-resistant or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very fascinated with A Step-by-Step Guide to Installing a Bathtub and I am praying you enjoyed the page. For those who enjoyed our post if you please don't forget to pass it around. Thanks for your time invested reading it.
About This
Report this page